My 15

Post pics and info of your rides here split windows only

Moderators: warb, Rawdyn, Leroy, byronbus, Tonz Magonz, dmb

User avatar
Raiz
DSKer
Posts: 94
Joined: Wed Jul 24, 2013 2:30 pm
Location: Cockle bay NZ

My 15

Post by Raiz »

My build... confusing as I changed my mind a lot so bere with me..

ok so when i got it first thing was to sort the spindals for dropped. Creative sorted these. then with tyres and whitewalls to boot.
Next up was a dual cicuit master cylinder with new lines all round as i go, 1974 on a single circuit! lol
Image


So now the rear end is up and i'm fitting bug S/A using Wagenwest offset bagged plates, i bought old bug hubs to keep the wide 5 for now..
Image

gonna be plumbing in the Air this weekend along with the rest of the brake lines. i hope to get the rear done as the Airbeam arrives any day now.
Lee

The lord is not my shepherd for I am not a sheep....
User avatar
Raiz
DSKer
Posts: 94
Joined: Wed Jul 24, 2013 2:30 pm
Location: Cockle bay NZ

Re: My 15

Post by Raiz »

Ok so today i continued with the dual circuit brakes.

Image

Also got the Shocks in, rear bags all plumbed in, and new bearings and hubs fitted.

Image

Sited the air valve block..

Image

And plumbed in the compressor and tank.

Image


All the air is installed subject to be moved again as i dont want it visable.
Lee

The lord is not my shepherd for I am not a sheep....
User avatar
Raiz
DSKer
Posts: 94
Joined: Wed Jul 24, 2013 2:30 pm
Location: Cockle bay NZ

Re: My 15

Post by Raiz »

So i got a bit of time on the bus today, fitting this bad boy!

Image

The chop saw made light work of the Leaves.

Image

Got the top run done then proceeded to the bottom tube, started to pull the leaves and!

Image

Oh well not a problem as there is just enough for me to loose in the narrowing....

Image

Maybe not.......Fk Fk n Double Fk
So now Where to buy some leaves from???
Watch this space.....
Lee

The lord is not my shepherd for I am not a sheep....
User avatar
Raiz
DSKer
Posts: 94
Joined: Wed Jul 24, 2013 2:30 pm
Location: Cockle bay NZ

Re: My 15

Post by Raiz »

Sup Fella's
So i thought whilst i'm waiting on some Beam leaves i may aswell get under the bus and sort this Steering box.

Image

Image

Image

Image

Image

And primed up
Image

one less thing to worrie about...
Image
Lee

The lord is not my shepherd for I am not a sheep....
User avatar
Raiz
DSKer
Posts: 94
Joined: Wed Jul 24, 2013 2:30 pm
Location: Cockle bay NZ

Re: My 15

Post by Raiz »

Got me leaves today so managed to build up the beam at last.

Image
Lee

The lord is not my shepherd for I am not a sheep....
User avatar
Raiz
DSKer
Posts: 94
Joined: Wed Jul 24, 2013 2:30 pm
Location: Cockle bay NZ

Re: My 15

Post by Raiz »

Beam a long time coming but in she goes.
Image

Image

So cause i've been gagging to see how she sits i cut loads of corners for a quick mock up with the rims on..

Image

Image

Image

Image

Image

So heres the money shot...well subject to tubbidge as i was laid on the arches.
Image

so chuffed how she looked but popped her back up to start connecting shit...
So since adding the air my chassis started to look like a utillitys super highway, so i decided to hide it all in some Copex conduit..
Image

Another little upcoming item is my Bay/Stinkfoot tank..lol with one or two too many pipes ? any ideas would be appreciated, i'm guessing i need 1 for breather..
Image

Just a little update on the prep of the new Stinkfoot tank..

Image

After a shake about i poured out this...

Image

Realized some prep is really needed.
However from these shots it seems a bit localized...

Image

Proceeded to breakdown the nastys with this stuff i got from a previous employer..

Image

To say this stuff is pokey is an understatement as i spilt a loads and it ripped the shit out the concrete floor...

Image

So when this is completely dry i'm gonna reseal it with some of this stuff from Frost's..

Image

O and another recent purchase is 8 Porsche teledials only need four but won 8... sweet!
I plan to powdercoat and prep these Black like 56oldcrows... i really liked the look.

Image

Image


So today i done the Tank swap...

Image

After removed this is them together, i had to modifie the neck to make fit.

Image

Image

Cause its a bigger tank i needed to extend the straps by 5 inch's..

Image

Image

All fitted

Image

and got the engine fitted and run her up for the 1st time since it came back from the dock...

Image

She Breathes!

Image
Lee

The lord is not my shepherd for I am not a sheep....
User avatar
Raiz
DSKer
Posts: 94
Joined: Wed Jul 24, 2013 2:30 pm
Location: Cockle bay NZ

Re: My 15

Post by Raiz »

scored some Porsche brakes, need stripping cleaning and painting 1st.

As you can see by the pictures the backing plates took some pain in transport, can i just loose these as they seem pretty fooked.?

Image

Image



Thought i'd mock up me new Porsche discs this eve..

Image

Image

Think the Offset is real good on these as they stay nicely tucked...

Image


To pissed for a decent write up so here are some pictures cause i done some stuff today on the bus.

Image

Image

Image

Image

Image

Oh yeah i planned on actaully rolling out the garage but my battery was fooked and i couldnt push it cause i was laid on the arches etc..(sorry bout that)
Lee

The lord is not my shepherd for I am not a sheep....
User avatar
Raiz
DSKer
Posts: 94
Joined: Wed Jul 24, 2013 2:30 pm
Location: Cockle bay NZ

Re: My 15

Post by Raiz »

Today i sorted my clutch out so was able to run the bus outside :o albeit with no brakes :?

The engine was not running right thats for sure, i'm going to get it set up correct when i fit the electronic ignition...hopefully with a new zorst by then.

my steering box has loads of play...i hoped the spindals and the new beam would of helped but the majority of the play was at the box, something to pull apart another day..

As some of you may of read i am going to swap to IRS sometime? i've bought a 1986..944T rear setup

Image

As you can see monster Brembo's on the back so after some research i will be swapping these with the hubs for the early non turbo to match the front :o my reasons is the brakeing should be more than efficiant and i wont have issues with what size rims etc..


Image

Image

[youtube]http://www.youtube.com/watch?v=9tgBzWjPvoU[/youtube]

[youtube]http://www.youtube.com/watch?v=xEt9Z-S8yuI[/youtube]

Today i started to pull the bus apart again to start the big job of sorting the metal....and fit that IRS :o Eventually at least..
As your probely wondering, my plans for rolling next year have been shelved... i really dont see the sense in MOT and tax etc for one year just to find any issues with a rear setup im not sticking with...

So exciting times ahead, for me all unknowns :o

Image

Image

I hope to build a chassis tilter next time out (after ive made space) so i look forward to that... see ya soon


Next i had to pimp up the welder a bit... loose the farty little cylinder...

Image

Image

Next i got a pile of steel cut almost to length... along with some wheels sourced F.O.C

Image

At this point i should add my welding skillz are not even close to most of you on here as ive not done much before :o says the man stripping a bus :lol:
Oh and this chassis tilter was c/o MKBUGGS who kindly contributed it in the technical thread... :drinkers:
Didn't get it finished but heres the start of it.

Image

Carried on stripping the bus today along with pulling stuff out for selling as space is needed now...

some crusty battery tray pending sorting

Image

Image

And a pile of rubbish this had to go 4 sure..

Image
Lee

The lord is not my shepherd for I am not a sheep....
User avatar
Raiz
DSKer
Posts: 94
Joined: Wed Jul 24, 2013 2:30 pm
Location: Cockle bay NZ

Re: My 15

Post by Raiz »

So i knew there was some filla present.. so i wanted to pull some off to see.
It was certainly thick thats fo sho.. looks like i uncovererd a shit repair as after a few taps, so much rust fell out.
i think the repair was laid ontop of the old shit?

Image

Image

Image

check the heep from under that one section :o

Image

So i am now concidering getting the shell media blasted as this will remove the shite so i can see whats what..

So today i continued building the chassis tilter.. came together well but unfortunatly due to the hight in my garage at the highest point it JUST bloody fails the roof timbers :evil: now its when im rolling off the 45 degree leg as the edge being square creeps just 1 or 2mm to high..
So i got 2 choices slice and angle off the 45 so as to maintain current hight or fit another set of wheels and roll it outside then wheel it back in..
I dont want to trim the 45 as its size and surface area mean its perfect balance when on it, and to alter that might make that angle unusable.. :roll:
So next out i shall fit some castors and rework my plan.. :wink:

escuse the lack of progress pics today as didnt have camera till later on.

Image

Image

Image

So with another 4 wheels on the frame i flipped the pea in readiness for Rail notching, and outriggers, Jacking points, plus a few over shitty bits..

Image

Image

Image

Image

Image
Lee

The lord is not my shepherd for I am not a sheep....
User avatar
Raiz
DSKer
Posts: 94
Joined: Wed Jul 24, 2013 2:30 pm
Location: Cockle bay NZ

Re: My 15

Post by Raiz »

Had a morning on the bus so pulled some stuff from my chassis, airlines and controller etc..

Disconnected

Image

Probely wont refit this as i dont like it! its too fiddly and not a fixed type.
so i wanna keep digital display but something i can mount?

Image

Next i made a start to the chassis notching.. well marked out and cut the tube to weld in..

Image

Image

Image

Image

Image

My welds seem to be getting better too :) but realized i wanted to get the bus over onto its other side as im still not confident welding upside down (advice welcome :wink: )

so with this in mind i started to add another two removable 45 degree legs so i can tilt and finish my rail notchs..

Image

Image

Image

Image

Image

Image

Image


today i rolled the bus outside to lay her on the new 45 degree angles so i could finish those notch welds, and true to form the good ol british weather turned bang on cue :evil:

Image

Then i rolled her over to the otherside so i could attack the roof nice n easy..

Image

I spent ages marking out inside and out...

Image

No turning back now :o

Image

Image

now with a nice chunk or metal for some repair on my way.. :wink:

Image

As you can see quite alot lighter at the moment :?

Image

Not the best place for my little man to be today, alot of sharp stuff about :ANAL: It is great hearing him come in going "CAMPER CAMPER CAMPER" :)

Image

Today i bunked off work early and had a little sesh on the bus :wink:

Removed bump stop bag mount and shock clamp thing :shock:

Image

then stood inside the bus to get a picture of some more shitty bits lurking under paint and bondo :roll:

Image

theres 3 of these repairs on the cab floor, just plonked straight ontop of old shite :twisted:

Image

Dusty mc dustyfucker

Image
Lee

The lord is not my shepherd for I am not a sheep....
User avatar
Raiz
DSKer
Posts: 94
Joined: Wed Jul 24, 2013 2:30 pm
Location: Cockle bay NZ

Re: My 15

Post by Raiz »

Did i bunk off of work early again :evil: hell yeah :wink:
so as a result i got some garage time in..
So since i cut a huge hole in the roof ive been meening to start sureing it up (giving it some strength)

so as i cut the thingy bob that hugs the roof? :? i needed to extend this so as to pick up my strengthening bar that will be fitted soon. so not pretty i know but i fabbed a couple of pieces to give me some length :butthead:

Image

welded on

Image

Image

Image

this along with the other short trusses will be flared and tacked onto the steal bar.. kinda like this

Image

As you can see in this pic the edge peices will be shortend as the bar will be inward 100mm ish and the extended piece will be at the back in the middle.

Image

Also i will need to shave this end to accomadate the rear curve in the roof.
Im thinking i might just bend it though?


Image

today i have mostly been doing stuff in my garage :D

at the front of my rear arch by the cargo door post has been hiding something so i cracked out the tool to remove the snot :roll:

Image

Another shite bit to remove n sort at some point soon :D the smile is although i dont like to find shite bits im enjoying doing all these repairs....

So back onto sorting the roof section around the hole i cut for the rag roof 8)

So i sliced the end in the shape required

Image

Image

Then with the centre section tacked in place

Image


Image

So whilst doing this work today i got a call from a geezer who has been sorting my rims 8) went and collected these and was well happy with the finish and the colour (this is the same white for the bus)

Insert bus porn here :P

Image

Image

Image


You see what im up against :twisted: :twisted: :roll:

Check the fake line up against the actual line :ANAL:

Image

More metal being added to the list daily

today i say bye bye fish eye..

Image

Image

Image

Tacked in place

Image

Image

Image

Just gotta finish the welds another time :)

Had a bloody good clearup in the garage today well an hour or so :roll:
Still loads of sorting to do, just wanna house all my bus bits new and old so i know when things get closer i know where to find em :)

So sorry but i had to see :wink:

Image

Tomorrow i get a day on the bus so hopefully another step closer......................to finding metal underneath

Today i removed the other front door (ive been putting this off due due rounded seized bolts) :evil:

Then i popped it over to the otherside to remove the bump stop and shock thingy..

Image

Image

Oh and must forget some more crust pictures :roll:

Image

Image

this is as far as i got as apparently the noise hasnt stopped all day and the neigbours are having a BBQ :ANAL: :roll:

Today i moved some more filler along the sill of the long panel again to see whats underneath :roll:

Check this repair :ANAL: :evil:

Image

Image

then i moved onto removing all locks and handles. i plan to send off all locks and ignition to have them worked off one key.

first problem was my cargo door has no lock?

Image

Today i exposed my long one :shock:







Image

tried to remove that last lock only to have the shaft snap off so i need a new handle anyways :roll:

So cause my bus is Brazillian it is a riot of random parts and panels and i was hoping someone could advise me on my arch (dogleg) panels see is it thin or thick lip model? need to get it right when getting new metal.

Image

Image

Also been concidering getting this original sellers badge tidied up to put back on when im done :? what ya think?

Image

second prob is how do i get this handle off? its the tailgate door.

Image

Image
Lee

The lord is not my shepherd for I am not a sheep....
User avatar
Raiz
DSKer
Posts: 94
Joined: Wed Jul 24, 2013 2:30 pm
Location: Cockle bay NZ

Re: My 15

Post by Raiz »

off to bed now... more to follow
Lee

The lord is not my shepherd for I am not a sheep....
evsky
DSKer
Posts: 368
Joined: Wed Nov 10, 2010 11:46 am
Location: central coast nsw

Re: My 15

Post by evsky »

This is a sweet build. Where are you from???
User avatar
067DUB
DSKer
Posts: 2868
Joined: Mon Oct 24, 2011 5:09 pm

Re: My 15

Post by 067DUB »

fkn oath, nice build.
User avatar
63 left hooker
DSKer
Posts: 1215
Joined: Tue Nov 24, 2009 1:03 pm
Location: Northern Beaches Sydney

Re: My 15

Post by 63 left hooker »

Great build, love the ride height!
Last edited by 63 left hooker on Fri Jul 26, 2013 6:54 am, edited 1 time in total.
61 dc
67 beetle
Post Reply