Page 3 of 7
Re: 60 panel
Posted: Fri Feb 05, 2021 8:00 pm
by warb
splitthis wrote:
Got a pic of what you mean mate? I think your asking about the bottom of the bulkhead which sits on the front of the front top hat and is below floor level? If so you can do the sides after the top hats and floor but the centre section (under the spare wheel section) needs to be done before floor as that’s where floor butts up against.
exactly mate, and tha thats what im doing, will most likely remove the lower bulkhead panel as its a hack job, install subfloor, than a new lower bulkhead when i get it.. the way i see it is the cargo floor welds to the bulkhead, not the forward tophat. however will be doing some more study, look over my yellow bus too.. always learning. BTW,pre assembled floor looks the goods so far.
Re: 60 panel
Posted: Sat Feb 06, 2021 4:08 pm
by spl65t
Nice one mate, remind me is it the red over the blue or vice versa ?
Re: 60 panel
Posted: Sat Feb 06, 2021 4:24 pm
by warb
spl65t wrote:Nice one mate, remind me is it the red over the blue or vice versa ?
Blue over red, may have been PMG, however none of the tell tale bits/holes. However has the weights on the drivers sill.. dunno.
Re: 60 panel
Posted: Sat Feb 06, 2021 6:40 pm
by D-Train
Pre gabbed floor looks good. Who’s one is that?
Re: 60 panel
Posted: Sat Feb 06, 2021 9:51 pm
by warb
D-Train wrote:Pre gabbed floor looks good. Who’s one is that?
BBT through allaircooled, looks solid and size looks correct, spacing of i beams and tophats are within a few mm, comes with the outriggers too..will strip back the primer to sus too, so far so good tho
Re: 60 panel
Posted: Sun Feb 07, 2021 5:30 pm
by D-Train
Fuxk yeah. Looks good
Re: 60 panel
Posted: Fri Feb 12, 2021 10:01 pm
by warb
Re: 60 panel
Posted: Sat Feb 13, 2021 6:43 am
by splitthis
Let the fun begin!
Re: 60 panel
Posted: Sat Feb 13, 2021 2:41 pm
by D-Train
Does the KF lower bulkhead not have the cutouts for the gear tube in the middle, or doesn’t it go down that far?
Re: 60 panel
Posted: Sat Feb 13, 2021 3:01 pm
by warb
D-Train wrote:Does the KF lower bulkhead not have the cutouts for the gear tube in the middle, or doesn’t it go down that far?
I have absolutely no idea, we're getting into it next Sunday maybe hopefully, let you know then mate!
Re: 60 panel
Posted: Sat Feb 13, 2021 4:48 pm
by D-Train
warb wrote:D-Train wrote:Does the KF lower bulkhead not have the cutouts for the gear tube in the middle, or doesn’t it go down that far?
I have absolutely no idea, we're getting into it next Sunday maybe hopefully, let you know then mate!
Epic! Thanks bloke!
Re: 60 panel
Posted: Mon Feb 15, 2021 7:11 am
by beerdoc
warb wrote:Ha, thinking of putting in a type3 hatch, dunno, have the panel to close up the hole tho...
Do the hatch Warby Trust me well worth it
Re: 60 panel
Posted: Mon Feb 15, 2021 8:20 pm
by warb
beerdoc wrote:warb wrote:Ha, thinking of putting in a type3 hatch, dunno, have the panel to close up the hole tho...
Do the hatch Warby Trust me well worth it
deal being done as i type
Re: 60 panel
Posted: Mon Feb 15, 2021 9:43 pm
by MID WEST DUBBER
warb wrote:beerdoc wrote:warb wrote:Ha, thinking of putting in a type3 hatch, dunno, have the panel to close up the hole tho...
Do the hatch Warby Trust me well worth it
deal being done as i type
149845504_428304705064431_1325597932861335195_n.jpg
I was thinking about this for my bus as well
Re: 60 panel
Posted: Tue Feb 16, 2021 3:04 pm
by warb
another peice of the puzzle.