Page 6 of 7
Re: 60 panel
Posted: Wed May 12, 2021 8:40 pm
by warb
spl65t wrote: ↑Wed May 12, 2021 7:46 pm
Nice one mate, did you work out what it says above the Tare weights etc.... ?
no idea man, any ideas? will loose quite of a bit of it when replacing the lower long side tho, in two minds if i match or just leave it raw and obvious.
Re: 60 panel
Posted: Thu May 13, 2021 4:27 pm
by spl65t
warb wrote: ↑Wed May 12, 2021 8:40 pm
spl65t wrote: ↑Wed May 12, 2021 7:46 pm
Nice one mate, did you work out what it says above the Tare weights etc.... ?
no idea man, any ideas? will loose quite of a bit of it when replacing the lower long side tho, in two minds if i match or just leave it raw and obvious.
Was that normally like the Farm/Property name above the weights .....generally ?
I see 'TON - C _ _ ? and also dead people
Re: 60 panel
Posted: Thu May 13, 2021 10:20 pm
by morts
[/quote] I see 'TON - C _ _ ? and also dead people
[/quote]
I see a squirrel...
Re: 60 panel
Posted: Sat Jun 05, 2021 3:02 pm
by warb
any tips on this bit?..espicall the panel between the inner and outer.. seems variable, depending on where the doors end up..
Re: 60 panel
Posted: Sat Jun 05, 2021 4:28 pm
by vanell
I like to do that last, or at least have both cargo doors on, I screw it all together with self tapping screws, and screw the floor in too, those sills are a pain in the arse, never seen a straight one, sometimes too long or have a twist in them, always a compromise, oh and by the way I see the red headed matchbox girl. Ian
Re: 60 panel
Posted: Sat Jun 05, 2021 5:50 pm
by warb
yeah man, pretty much came to that too, few others suggested last aswell, screwd in for now, next is the complete C pillar.
Re: 60 panel
Posted: Sat Jun 05, 2021 5:58 pm
by warb
from today, screwed into place for now.. one window rebuilt, not a bad as I remember it last time tho, all fit well. looking for a pair of latches too, ones I have are well worn..
also chasing the back of the inner RHS dogleg, and the panel in front of the rear RHS wheel arch, 7 or so inches up.
Re: 60 panel
Posted: Sat Jun 05, 2021 6:04 pm
by warb
cleand up the panels that came with.. still solid.
Re: 60 panel
Posted: Sat Jun 12, 2021 8:29 pm
by warb
just a mock up, however inner c piller out, plates made to swing the doors.. next one C piller in. maybe.,
Re: 60 panel
Posted: Wed Mar 23, 2022 6:33 pm
by warb
Putting it out there, any one have this cut at all?
Re: 60 panel
Posted: Wed Mar 23, 2022 8:14 pm
by vanell
I don’t think you made the squared out diagram big enough, you could have left the blue bit out and just showed the picture, come on mate, buy a whole side , Rusty’s thread shows you how to put it on
Re: 60 panel
Posted: Wed Mar 23, 2022 9:12 pm
by warb
vanell wrote: ↑Wed Mar 23, 2022 8:14 pm
I don’t think you made the squared out diagram big enough, you could have left the blue bit out and just showed the picture, come on mate, buy a whole side , Rusty’s thread shows you how to put it on
want to keep as much as the shitty look as i can, however this bit way too holey... may just buy the whole side yeah and cut what i need out of it.
Re: 60 panel
Posted: Thu Mar 24, 2022 7:12 am
by splitthis
Das/bus stop etc sell that. Search for “short sill” I think. I have a section somewhere but pretty sure it’s cut too low. I’ll check tonight.
Re: 60 panel
Posted: Fri Mar 25, 2022 10:34 am
by Griffin
Looking great mate
If you need the whole side let me know and will look after you, or can bring to Valla if you can wait that long!
We do the short side lower section but only for later buses sorry
https://allaircooled.com.au/products/co ... be41&_ss=r
Re: 60 panel
Posted: Wed Apr 20, 2022 1:34 pm
by warb
thanks man, you prob jsut saw, bought the later one, hopefully can cut it to suit, just need the lower bit,
Also chasing the lower a pillar repair section, left and right, also the small section that goes next to it, any leads at all?
Pics stolen from niko's videos
-
https://www.youtube.com/watch?v=KrqF3Iw ... emopGarage (top stuff)